got 2 pringles machines jamming, can see the prob but struggling for an answer to correct it, they are metal barrel pringles and the barrel is catching on bottom of next tub. if i hold segments slightly to left it vends perfect.
Anyone know how i can set segments to be slightly more to left? thinking they badly made machines.
Ade
pringles jamming
-
- Coin Op Group Grand Master
- Posts: 852
- Joined: July 6th, 2009, 7:43 pm
- Area Covered: east and west midlands
- Machines Used: kiddie rides, sweet and toy vend
- Referred by?: M.Slater
- Location: tamworth & b`ham + surrounding areas
Re: pringles jamming
guys ive listed one on ebay so dont bid on it, spent 4 hours trying to solve jamming and gave up lol
http://www.ebay.co.uk/itm/110895439192? ... _500wt_949" onclick="window.open(this.href);return false;
Ade
http://www.ebay.co.uk/itm/110895439192? ... _500wt_949" onclick="window.open(this.href);return false;
Ade
-
- Coin Op Group Master
- Posts: 740
- Joined: August 10th, 2009, 8:47 am
- Area Covered: London & Home Countie
- Machines Used: Bulk, Tower, Pringles & various toys
- Referred by?: Sarah Hickman
- Location: London & Home Counties North of Thames
Re: pringles jamming
Ade,
The problem you have is the rings are not alligned properly. Unlike the snack towers the is only one position that has the correct alignment when siting the centre lug on the ring onto the black bottom bit.
Pete
The problem you have is the rings are not alligned properly. Unlike the snack towers the is only one position that has the correct alignment when siting the centre lug on the ring onto the black bottom bit.
Pete
-
- Coin Op Group Grand Master
- Posts: 852
- Joined: July 6th, 2009, 7:43 pm
- Area Covered: east and west midlands
- Machines Used: kiddie rides, sweet and toy vend
- Referred by?: M.Slater
- Location: tamworth & b`ham + surrounding areas
Re: pringles jamming
Pete,
ive been through every possible lining up scenario mate lol, ive moved black ring round, ive turned segments, they will only line up over chute on one setting, if i move segments round and leave black ring in one position, the drop line doesnt line up with barrel. i even drilled and re riveted the black plastic piece that the black ring sits on and moved it slightly to left, but that didnt work.
Ade
ive been through every possible lining up scenario mate lol, ive moved black ring round, ive turned segments, they will only line up over chute on one setting, if i move segments round and leave black ring in one position, the drop line doesnt line up with barrel. i even drilled and re riveted the black plastic piece that the black ring sits on and moved it slightly to left, but that didnt work.
Ade
- FlintVending
- Coin Op Group Master
- Posts: 564
- Joined: January 21st, 2009, 10:47 pm
- Area Covered: Norfolk, Suffolk, Cambridge
- Machines Used: Bulk, Tower, Pringle, rings and pills, lighters
- Location: Norfolk, suffolk
Re: pringles jamming
I used a bit of brute force and ignorance and took a hammer to the leading edge of the barrel, it worked for me, but dont hit it to hard as they are brittle!
- FlintVending
- Coin Op Group Master
- Posts: 564
- Joined: January 21st, 2009, 10:47 pm
- Area Covered: Norfolk, Suffolk, Cambridge
- Machines Used: Bulk, Tower, Pringle, rings and pills, lighters
- Location: Norfolk, suffolk
Re: pringles jamming
AdeAde wrote:guys ive listed one on ebay so dont bid on it, spent 4 hours trying to solve jamming and gave up lol
http://www.ebay.co.uk/itm/110895439192? ... _500wt_949" onclick="window.open(this.href);return false;
Ade
You should really mention that it jamms in the listing unless you want to go as low as some of the suppliers that is !
-
- Coin Op Group Grand Master
- Posts: 852
- Joined: July 6th, 2009, 7:43 pm
- Area Covered: east and west midlands
- Machines Used: kiddie rides, sweet and toy vend
- Referred by?: M.Slater
- Location: tamworth & b`ham + surrounding areas
Re: pringles jamming
FlintVending wrote:I used a bit of brute force and ignorance and took a hammer to the leading edge of the barrel, it worked for me, but dont hit it to hard as they are brittle!
yeah i hacksawed each side of barrel with the intent of banging edge down but was worried i would do more damage, might try it again nige
Ade
-
- Coin Op Group Grand Master
- Posts: 852
- Joined: July 6th, 2009, 7:43 pm
- Area Covered: east and west midlands
- Machines Used: kiddie rides, sweet and toy vend
- Referred by?: M.Slater
- Location: tamworth & b`ham + surrounding areas
Re: pringles jamming
FlintVending wrote:AdeAde wrote:guys ive listed one on ebay so dont bid on it, spent 4 hours trying to solve jamming and gave up lol
http://www.ebay.co.uk/itm/110895439192? ... _500wt_949" onclick="window.open(this.href);return false;
Ade
You should really mention that it jamms in the listing unless you want to go as low as some of the suppliers that is !
ive warned everyone on forum not to bid on it nige, cant be fairer than that, ive bought some right crap off ebay
Ade
-
- Coin Op Group Master
- Posts: 740
- Joined: August 10th, 2009, 8:47 am
- Area Covered: London & Home Countie
- Machines Used: Bulk, Tower, Pringles & various toys
- Referred by?: Sarah Hickman
- Location: London & Home Counties North of Thames
Re: pringles jamming
Ade,
Not a clenport then?
Pete
Not a clenport then?
Pete
-
- Coin Op Group Grand Master
- Posts: 852
- Joined: July 6th, 2009, 7:43 pm
- Area Covered: east and west midlands
- Machines Used: kiddie rides, sweet and toy vend
- Referred by?: M.Slater
- Location: tamworth & b`ham + surrounding areas
Re: pringles jamming
PGBrew wrote:Ade,
Not a clenport then?
Pete
not sure mate, its one that to get to coin mech you have to take plastic rim of top of base
Ade